Vogue Industrial ABOVE GROUND SWIMMING POOL Specifications download pdf (Page 11)

CLOSING THE WALL

Overtightening the nuts could cause the screws to fracture which could result in pool failure. Failure to tighten the

nuts sufficiently could also result in pool failure. This is one of the most important structural assembly aspects you will

perform. Be absolutely sure you have assembled the wall as shown above for your pool.

Manufacturer can not assume the responsibility of the performance of this product if the

instructions of closing the wall are not followed exactly.

Pool Wall

4 CLOSURE

BARS

1/4" x 20 x 3/4"

TRUSS HEAD

SCREW

INSIDE

OF POOL

1/4" x 20

SERRATED

FLANGE NUT

DANGER

YOU MUST ASSEMBLE THE

POOL WALL

AS PER INSTRUCTIONS

USE ALL THE 3/8-16x3/4"

TRUSS HEAD SCREWS,

WASHERS AND 3/8-16

SERRATED FLANGE NUTS

TO CLOSE POOL WALL.

DO NOT LEAVE ANY

OPEN HOLES

TIGHTEN EACH SCREW

TO 85 INCH POUNDS.

View from

the top

3/8" TRUSS

HEAD SCREW

WASHER

3/8 FLANGE

NUT

Pool Wall

Recessed

Posi-Lock System

During the manufacturing process, the

one end of the pool wall will have a

slight crease or bend in it. Straighten

out this bend as best as possible, and

assemble the pool wall putting this end

of the wall on the outside as shown.

INSIDE POOL

OUTSIDE

POOL

POOL WALL

DANGER

YOU MUST ASSEMBLE THE POOL

WALL AS PER INSTRUCTIONS

USE ALL THE

1/4"-20x3/4" TRUSS HEAD SCREWS

AND 1/4"-20 SERRATED FLANGE

NUTS TO CLOSE POOL WALL.

DO NOT LEAVE ANY OPEN HOLES

TIGHTEN EACH SCREW TO 85

INCH POUNDS.

Insert the 1/4" - 20x3/4" truss

head screws from inside the pool

through the preattached inside

closure bar, through inside and

outside wall ends, and through

outside closure bar.

The 1/4" serrated flange nuts are

secured to the screws on the out-

side of the wall. All the holes must

match and be secured together with

the screws and nuts provided.

Tighten each screw and nut to 85

inch pounds of torque. If no torque

wrench is available, tighten each nut

until snug. Then tighten each nut

one (1/2) half additional turn. If nut

appears to be lose after tightening,

please check if the screw is stripped

or broken. It must be replaced.

During this assembly procedure, make sure that

one washer is on the inside of the pool, and one

washer in on the outside of the pool sandwiching

the two wall ends between them. Also ensure that

the recesses of the walls and washers all face the

same direction. Align the holes in the wall ends.

From the inside of the pool, insert a

3/8 Truss Head screw through the

washer, through the holes on the

inside and outside wall ends, and

through the second washer.

Fasten with 3/8 serrated flange nut

on the outside of the pool having the

flange of the nut face the washer. Only

hand tighten the nuts at this point.

Continue for each hole in the wall

ends.

DO NOT LEAVE ANY OPEN HOLES.

Tighten all screws and nuts to 85 inch

pounds. If no torque wrench is avail-

able, tighten each nut until snug. Then

tighten each nut one half (1/2) addi-

tional turn. If nut appears to be lose

after tightening, please check if the

screw is stripped or broken. If it is, it

must be replaced.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 24 25

Comments to this Manuals

No comments

Vogue Industrial ABOVE GROUND SWIMMING POOL Specifications Page 11

Comments to this Manuals

Related products and manuals for Above ground pools Vogue Industrial ABOVE GROUND SWIMMING POOL